Setting Vsd MM44013

SETTING VSD MICROMASTER 420,440 (SIEMENS)

A. METHOD FOR QUICK COMMISSIONING

P10 =1,

START OF QUICK COMMISSIONING

P304 =MOTOR VOLTAGE RATING

P305 =MOTOR CRRENT

P307 =MOTOR POWER RATING (KW)

P308 =MOTOR COSØ RATING
P311 =MOTOR RPM RATING

P700 =SELECTION OF COMMAND SOURCE

=1, FOR MANUAL OPERATION

=5, FOR USS COMMUNICATION

=6, FOR PROFIBUS

P1000 =SELECTION OF COMMAND SOURCE

=1, FOR MANUAL OPERATION

=5, FOR USS COMMUNICATION

=6, FOR PROFIBUS COMMUNICATION

P1120 =RAMP UP TIME IN SECONDS (0-650SECONDS)

P1121 =RAMP DOWN TIME IN SECONDS (0-650SECONDS)

P3900 =1,

P305=Motor current ( Very important )

P610=1

P640=100

P290=1

                    B) MISCALENOUS PARAMETERS

P3 =3,TO SEE ALL THE PARAMETERS

R21 = TO CHECK THE MOTOR FREQUENCY

R27 = TO CHECK THE MOTOR CURRENT

P5 =DISPLAY SELECTIION

=21, FOR CONTINUOUSDISPLAY OF FREQUENCY

=27,FOR CONTINUOUS DISPLAY OF CURRENT

=25, FOR CONINUOUS DISPLAY OF VOLTAGE

P295 =INVERTER FAN OFF DELAY TIME (0-3600 SECONDS)

P918 =INVERTER PROFIBUS ADDRESS

R947 =LAST FAULT CODE

=947[0], FAULT 1

=947[1], FAULT 2

=947[2], FAULT 3

R949 =FAULT VALUE

=949[0], FAULT VALUE 1

=949[1], FAULT VALUE 2

=949[2], FAULT VAULE 3

R967 =CONTROL WORD1

P1820 =REVERSE OUTPUT PHASE SEQUENCE

P1031 =SETPOIT MEMORY OF THE MOP

=0, MOP SETPOINT WILL NOT BE STORED

=1, MOP SETPOINT WILL BE STORED

         C) PROCEDURE FOR FACTORY RESET

P10 =30

P970 =1

          D) PROCEDURE FOR SETTING USS COMMUNICATION

i) FACTORY RESET THE DRIVE

ii) PERFORM QUICK COMMISSIONING

P2012 =2, USS PZD LENGTH

P2013 =127, USS PKW LENGTH

P700 =5, COMMAND SOURCE SELECTION

P1000 =5, FREQUENCY SOURCE SELECTION

P2009 =0,

P2010 =BAUD RATE

=5, 4800 BAUD

=6, 9600 BAUD

=7, 19200 BAUD

=8, 38400 BAUD

=9, 57600 BAUD

=12, 115200 BAUD

P2011 = INVERTER USS ADDRESS (0-31)

   E) PROCEDDURE FOR SETTING IF HARD WIRE OUTPUTS ARE USED

i) FACTORY RESET THE DRIVE

ii) PERFORM QIUCK COMMISSIONING

P700 =2,TERMINAL INPUT

P701 =16, FIXED FREQUENCY 1

P702 =16, FIXED FREQUENCY 2

P1000 =3, FIXED FREQUENCY

P1001 =VALUE OF FIXED FREQUENCY 1 ( EXAMPLE 25 HZ)

P1002 =VALUE OF FIXED FREQUENCY 2 (EXAMPLE 25 HZ)

PROCEDURE TO GET 4-20 MILLI AMPERE FROM TERMINAL 12, 13 OF THE

DRIVE

P771 =21, IF OUTPUT IS NEEDED CORRESPONDING TO FREQUENCY

=27, IF OUTPUT IS NEEDED CORRESPONDING TO CURRENT

P778 =4, VALUE Y1 FOR DAC SCALING

P780 =20, VALUE Y2 FOR DAC SCALING

P777 =0, VALUE X1 FOR DAC SCALING

P779 =50.09, VALUE X2 FOR DAC SCALING

P776 =0, IF 1 IS SELECTED 0-10VDC WILL APPEAR ACROSS 12,13 (PROVIDED

500

R774 =ACTUAL DAC VALUE IN MA





(BREAKING RESISTOR IS CONNECTED BETWEEN 12,13 OF DRIVE)Note to prevent the motor from getting failed due to over current**//END OF QUICK COMMISIONING